W edding card using Stampin' Up! products.
Project Recipe
Cut cardstock, designer paper, foil sheets, and Adhesive Sheets pieces to the following sizes using a Paper Trimmer:
- card from Blueberry Bushel Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" of starburst rays of blues and purples design from Full Of Life 6" x 6" Designer Series Paper, cut so the center of the rays is in the center of the rectangle and the light blue ray is in the upper right corner
- 3" x 3-1/2" from Basic White Cardstock
- 2" x 3-1/2" of silver foil from Brushed Silver & Gold Foil 12" x 12" Specialty Paper
- 1-7/8" x 3-3/8" from Adhesive Sheets
- 1-1/4" x 3" from Basic White Cardstock
- 1-1/2" x 2" from Blueberry Bushel Cardstock
- 1-3/8' x 1-7/8" from Adhesive Sheets
- 1-1/2" square of blue and purple watercolor wash design from Full Of Life 6" x 6" Designer Series Paper
- scraps of Real Red Cardstock
Adhere the starburst Full Of Life Designer Paper rectangle to the front of the Blueberry Bushel card so the light blue ray is in the upper right corner.
As you are ready to stamp using the Classic Wedding Set, place the cardstock on the Stampin' Pierce Mat. Using the mat will help you get a cleaner image each time you stamp. Put a piece of Grid Paper on top to protect the Mat from ink.
Mount the large, solid car body image from the Classic Wedding Set on Block E. Ink it up with the Berry Burst Ink Pad. Stamp it in the center of the large horizontal white rectangle so it is slightly closer to the top.
Mount the large, outline car with tires image from the Classic Wedding Set on Block E. Ink it up with the Tuxedo Black Memento Ink Pad. Stamp it over the top of the previously stamped car body image on the white rectangle.
Pick out the matching car die from the Classic Wedding Dies. Put it on top of the stamped image on a platform on your Stampin' Cut & Emboss Machine so it is centered over the image. Run through the machine.
Mount the set of three back window panes image from the Classic Wedding Set on Block B. Ink it up with the Balmy Blue Ink Pad. Stamp it inside the rear window area of the car cut out.
Mount the interior tire image from the Classic Wedding Set on Block B. Ink it up with the Tuxedo Black Memento Ink Pad. Stamp off once on Grid Paper, then stamp it inside one of the tire areas on the car cut out. Re-ink the stamp, stamp off, and stamp it inside the other tire area.
Peel the protective backing off of the larger Adhesive Sheets rectangle. Adhere the Adhesive Sheets rectangle to the white side of the silver foil rectangle. Be sure to leave the other protective backing in place for now.
Pick out the bumper die and the set of window frame/tail lights/back handle die from the Classic Wedding Dies. Put them on top of the silver foil rectangle on a platform on your Stampin' Cut & Emboss Machine so the silver side is face up and you leave room in one corner to cut out the cans in a later step. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces. Leave the set of window frame/tail lights/back handle die out. Keep the remainder of the silver rectangle.
Carefully remove the protective backing from the back of the bumper cut out. Adhere it to the bumper area on the car cut out.
Carefully remove the protective backing from the back of the window frame cut out. Adhere it to the window area on the car cut out.
Carefully remove the protective backing from the back of the back handle cut out. Adhere it to the back handle area on the car cut out.
Put the window frame/tail lights/back handle die on top of the Real Red scrap on a platform on your Stampin' Cut & Emboss Machine so you'll cut out two tail lights. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces.
Use Multipurpose Liquid Glue to adhere the tail lights cut outs to the tail lights areas on the the car cut out.
Adhere the completely stamped and layered car cut out to the front of the card so it is centered over the center of the starburst pattern as shown.
Mount the banner image from the Classic Wedding Set on Block H. Ink it up with the Berry Burst Ink Pad. Stamp it in the center of the remaining white rectangle.
Mount the "just married" sentiment from the Classic Wedding Set on Block B. Ink it up with the Berry Burst Ink Pad. Stamp it in the center of the previously stamped banner image.
Pick out the matching banner die from the Classic Wedding Dies. Put it on top of the stamped banner image on a platform on your Stampin' Cut & Emboss Machine so it is centered over the image. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces.
Use Mini Stampin' Dimensionals to adhere the banner cut out to the front of the card so it is centered across the trunk of the car cut out as shown.
Peel the protective backing off of the smaller Adhesive Sheets rectangle. Adhere the Adhesive Sheets rectangle to one side of the Blueberry Bushel rectangle. Be sure to leave the other protective backing in place for now.
Pick out the bow with strings and cans die from the Classic Wedding Dies. Put it on top of the Blueberry Bushel rectangle on a platform on your Stampin' Cut & Emboss Machine so the Blueberry Bushel (blue) is face up. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces.
Carefully remove the protective backing from the back of the bow/strings/cans cut out. Adhere it to the front of the card as shown so the bow is centered between the back handle and the bumper.
Mount the set of 3 cans image from the Classic Wedding Set on Block B. Ink it up with the Berry Burst Ink Pad. Stamp it in the remaining corner of the silver foil sheet. Try not to let the images smear as you stamp them. Set them aside to let dry for a bit.
Firmly press the stamped cans image against some Grid Paper to remove excess ink.
Pick out the matching three cans die from the Classic Wedding Dies. Put it on top of the stamped cans on a platform on your Stampin' Cut & Emboss Machine so it is centered over the images. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces.
One at a time, carefully remove the protective backings from the backs of the cans cut outs. Adhere them over the cans at the bottom of the bow/strings/cans cut out.
Pick out the set of three little hearts die from the Classic Wedding Dies. Put it on top of the small Full Of Life Designer Paper square on a platform on your Stampin' Cut & Emboss Machine. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces.
Use Mini Stampin' Dimensionals and a tiny piece cut from the edge of the Dimensionals sheet to adhere the three hearts to the front of the card as shown over the top of the car image.